|
Maasturiprojektit Osio on tarkoitettu etenkin pidempiaikaisten projektien seuraamiseen. Tämä on oikea paikka oman auton esittelyyn. |
|
Työkalut | Etsi tästä viestiketjusta | Näkymä |
#51
|
|||
|
|||
silly question
This may sound silly, but trying to understand what I need to rebuild these axles.
I know I need the large oil seal and adapter ring, pictured. I assume there are four of these??? I need the boot. are there four of these also? Here is what I have bought already, 4 different bearings and only two seals (only two each.??) Drive gear (upper/small gear) _ I have four of each of these….. SKF/FAG 6210 (single row radial ball, open) - dims: 50x90x20 INA BK4520 (drawn cup closed needle bearing) - dims: 45x52x20 Driven gear (lower/large gear) Timken JLM104948 (tapered roller/cone) same as LC Timken JLM104910 (tapered race/cup) same as LC Timken JLM508748 (tapered roller/cone) Timken JLM508710 (tapered race/cup) Seals, - I only have 2 of each of these…. Do I need four???? CR 23451 (STEFA, BB - dims:60x85x8), upper portal/axle tube oil seal CR 19687 (STEFA, BB - dims:50x90x10), inner hub grease/oil seal |
#52
|
|||
|
|||
front axle is in
Front axle installed.
|
#53
|
|||
|
|||
learn by image
Read the manual several times, still don't quite understand how to take out the main part to turn on the lathe. Anyone have pictures or description of how to take this apart?
|
#54
|
||||
|
||||
What part you are talking? Pinion flange, wheel hub or something else?
|
#55
|
|||
|
|||
I don't know if I am using the right term. Trying to get the part that has the lug studs, that I need to turn down on the lathe.
Is this the Hub? On the diagram, is the arrows pointing to the bolts to remove? Viimeksi muokannut 1fzpower : 20.04.2018 14:43 |
#56
|
||||
|
||||
Lainaus:
I never done it myself, but that shouldn't be too difficult task if you have (hydraulic) press available. |
#57
|
|||
|
|||
making progress
Well, there they were, about 8 bolts behind the drum brakes. Took those off, then had to run the the store to find the M8 - 1.0 thread bolt to press out the hub, but it worked really easy.
|
#58
|
|||
|
|||
then got it on the lathe
Started getting it turned down.
|
#59
|
|||
|
|||
Well good news and bad news.
Timo shipped off the parts a few weeks ago; however, they came back to him. He is unsure what happened or why, so looking for other shipping options like DHL. Anyone have a great way to ship parts to the US? Thanks, |
#60
|
||||
|
||||
Lainaus:
They bring cars, motorcycles and parts from USA to Finland all the time. Maybe you could ask do they work to the opposite direction, and bring your parts from Finland to USA?
__________________
- En pidä teistä. |
#61
|
|||
|
|||
pause
My sister was traveling around Finland/Sweden so she arranged to pick up the parts, so they are headed back to the US.
Otherwise, not much has been done. |
#62
|
||||
|
||||
Hah, I visited couple of weeks ago in Seattle and West Coast. Brought back to Finland 2 x rear axle shafts, rear drive shaft, front fender flares, hydro assit goods and plenty of smaller parts all in the luggage. I couldn't imagine somebody is dragging car parts in the opposite direction.
|
#63
|
||||
|
||||
Lainaus:
So, Offroaders just keeps planet in balance
__________________
- Levannon We(l)ho - |
#64
|
|||
|
|||
Lainaus:
|
#65
|
|||
|
|||
progress
Made a bunch of progress on the lathe, then went and used a friends mill. If anyone wants to do this work, I tried my best to post up how to do it on my thread on IH8MUD.
https://forum.ih8mud.com/threads/wha...#post-11866760 but, here is where it stands now. |
#66
|
|||
|
|||
more progress
more progress.....
sandblasted axles and put 3 coats of epoxy primer and then 3 more coats of john deere blitz black paint. |
#67
|
|||
|
|||
I had to put two small screw to keep the brake disk on correct place while the wheel nuts are loose. It worked without in garage but on real life the disk was able to move when I changed the tires. After a while the disk was vibrating and it led to soft brake pedal.
|
#68
|
|||
|
|||
Lainaus:
|
#69
|
|||
|
|||
sad day
I finally got to the point to put this all together, and the brake brackets are not the correct size. Don't know if I got the wrong disc, but the holes for the caliper needed to be out about 1/4 more and there is not enough material to drill new holes. I could turn down the rotor; however, decided to throw these brackets out and start over with my own parts.
|
Käyttäjiä lukemassa tätä viestiketjua: 1 (0 jäsentä and 1 vierasta) | |
|
Samanlaisia viestiketjuja | ||||
Viestiketju | Aloittaja | Foorumi | Vastauksia | Viimeisin viesti |
hi, where to get Volvo portal axles reasonably | jprscprs | Tekniikka & Jutustelu | 1 | 30.07.2016 19:59 |
Volvo Portal Power Meeting 2010 | KooPee | Tapahtumat | 41 | 02.04.2010 06:24 |
VOLVO PORTAL POWER MEETING 2009! | KooPee | Tapahtumat | 51 | 12.04.2009 06:49 |
More Volvo Portal Power Events | ASuur | Tapahtumat | 25 | 27.06.2007 23:11 |
Volvo "Portal Power Meet" | A45 | Tapahtumat | 82 | 09.03.2006 23:42 |